The Peavey IPR 1600 stereo power amp features 830 watts per channel at 2 ohms and weighs in at 7 pounds! The IPR1600 also has 2 channel independent fourth order Linkwitz-Riley crossovers, a variable-speed fan housed in a lightweight aluminum chassis, patented DDT speaker protection, and the revolutionary new IPR class D topology.
Boasting a net weight as low as 7 lbs., the groundbreaking Peavey IPR Series of pro audio power amps utilize an advanced design that allows Peavey engineers to dramatically reduce weight while increasing output power, reliability and thermal efficiency. IPR Series amplifiers are designed with a resonant switch-mode power supply and a high-speed class D topology that yields the highest audio resolution and efficiency available. And all at a cost that shatters the old-guard paradigm of power-amp valuation.
Shaking up the pro audio industry with innovative power amplifier designs has become a Peavey trademark. More than 30 years ago, Peavey was the first to break the $1-per-watt barrier. Now with the Peavey IPR Series, they've pushed technological limits again to bring you an amazingly powerful and efficient power amp for just pennies per watt.
The IPR DSP Series amplifiers feature the same power ratings, design and efficiency, plus a 32-bit processor with a suite of delays and crossovers, pre-programmed loudspeaker settings, stereo/mono operation, lockout—and for the first time in any power amplifier, built-in Waves® MaxxBass® technology, which uses psycho-acoustics to add more low-end to your system without the need for more power amps, processing or subwoofers.
Amps in the IPR DSP line contain presets for Peavey SP®, PR®, Impulse®, SSE™, QW®, PV® Series loudspeakers and monitors, as well as other commonly used loudspeaker configurations, plus special presets for program music applications (dance, speech, rock, thump, loudness, contemporary worship). Manual mode allows you to assign your custom crossover points, EQ, delay and more.
Peavey IPR1600 Stereo Power Amp Features:
- 2- Channel independent fourth-order Linkwitz-Riley crossovers
- DDT compression
- Revolutionary IPR class D topology
- Detented input controls
- Combi XLR 1/4" inputs
- Speakon output connectors
- Light Weight
- Individual signal pass 1/4" jacks on each channel
- LED illuminated
- Weight: 7.12 lb(3.23 kg)
- Width Packed: 12.44"(31.5976 cm)
- Depth Packed: 20.8"(52.832 cm)
- Height Packed: 4.72"(11.9888 cm)
Rated Power (2 x 2 ohms) - 800 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
Rated Power (2 x 4 ohms) - 530 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
Rated Power (2 x 8 ohms) - 300 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
Rated Power (1 x 2 ohms) - 1000 watts @ 1 kHz at <0.1% T.H.D.
Rated Power (1 x 4 ohms) - 600 watts @ 1 kHz at <0.1% T.H.D.
Rated Power (1 x 8 ohms) - 320 watts @ 1 kHz at <0.1% T.H.D.
Minimum Load Impedance - 2 ohms
Maximum RMS Voltage Swing - 55 volts
Frequency Response - 10 Hz - 50 kHz; +0, -3 dB at 1 watt
T.H.D. (2 x 2 ohms) - <0.1% @ 600 watts per channel from 20 Hz to 1.5 kHz, decreasing to 500 watts at 20 kHz at <0.25%
T.H.D. (2 x 4 ohms) - <0.1% @ 470 watts per channel from 20 Hz to 20 kHz
T.H.D. (2 x 8 ohms) - <0.1% @ 250 watts per channel from 20 Hz to 20 kHz
Input CMRR - > - 60 dB @ 1 kHz
Voltage Gain - x 60 (+35 dB)
Crossover - 100 Hz switchable 2nd order High pass and 3rd order Low Pass per channel
Crosstalk - > -70 dB @ 1 kHz at 100 watts power @ 4 ohms
Hum and Noise - > -105 dB, "A" weighted referenced to rated power @ 4 ohms
Damping Factor (8 ohms) - > 170:1 @ 20 Hz - 1 kHz at 8 ohms
Phase Response - +9 to - 86 degrees from 20 Hz to 20kHz
Slew Rate: - > 12V/us
Input Sensitivity - .775 volts +/- 3% for 1 kHz 4 ohm rated power, .68 volts +/- 3% for 1 kHz. 2 ohm rated power
Input Impedance - 15k ohms, balanced and 7.5k ohms unbalanced.
Current Draw @ 1/8 power - 550 watts @ 2 ohms, 390 watts @ 4 ohms, 250 watts @ 8 ohms
Current Draw @ 1/3 power -1,160 watts @ 2 ohms, 810 watts @ 4 ohms, 460 watts @ 8 ohms
Cooling - Temperature dependent variable speed 80 mm DC fan
Controls - 2 front panel attenuators, crossover select switch for H.P.F, Normal and L.P.F.
Indicator LEDs - 2 DDT (clip limiting), 2 Signal presence, 2 Active status, 2 Temp and 2 DC protect
Protection - Thermal, DC, subsonic, incorrect loads, under and over voltage
Connectors - Inputs: Dual Combi 1/4” XLR, Outputs: Dual 1/4” signal patch, dual Speakon connectors
Construction - 0.062” thick aluminum
Dimensions - 3.5”x19” x 10.5” behind front panel + 0.6” for handle
Dimensions Packed - 4.72” x20.8” x 12.44” (120mm x 530mm x 316mm)
Net Weight* - 3.23 kg (7.125 lbs.)
Gross Weight - 4.31 kg (9.5 lbs.)
Warranty - 5 years
Rated power readings made with BW: <10 Hz to 22 kHz. All power measurements made at 120 VAC and 240VAC.
2 ohm power is time limited by circuit breaker.
*Net Weight does not include power cord.
Help Others! Write a Review Today!
There are no reviews for this product.
If you've already purchased this product, we hope you have a moment to write a short review. When you take the time to write a review, you help millions of customers make a better buying decision! If you've ever read a customer review, then you know how helpful they can be when deciding to place an order! Please take a moment and write a review. You never know who you are helping in the process!